Hello to all Gilera fans , my name is Dimitrije (Dimitij) , i recently bought 1993 Gilera GFR 125 , and i`m planning to fully restore it .
It`s in a really bad shape , i`m hoping i can get some advice from other Gilera fans ...
Thanks..
Anyhow where can i post a new thread about my GFR ?
Hello from Serbia
Moderator: Joachim
- CokiGFR125
- Angstbremser
- Posts: 18
- Joined: Sun Jan 30, 2011 6:20 pm
- Location: Apatin / Vojvodina / Serbia
Hello from Serbia
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)
- Joachim
- Gileristi
- Posts: 11193
- Joined: Tue Dec 31, 2002 9:10 pm
- Location: Zweibrücken bzw. Landau/Pfalz
- Contact:
Re: Hello from Serbia
Just right hereCokiGFR125 wrote: Anyhow where can i post a new thread about my GFR ?
Good luck while finding parts. Everything seems to be very rare
If you need fairing parts, i can offer a source for replica parts from glass fibre.
ciao joachim
- CokiGFR125
- Angstbremser
- Posts: 18
- Joined: Sun Jan 30, 2011 6:20 pm
- Location: Apatin / Vojvodina / Serbia
Re: Hello from Serbia
Thank`s Joachim , i will make my own parts , i mean the fiber glass.
What i need is piston , piston rings , gasket set , brake pads etc ....
I will post a new build thread about my GFR.
What i need is piston , piston rings , gasket set , brake pads etc ....
I will post a new build thread about my GFR.
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)
- Joachim
- Gileristi
- Posts: 11193
- Joined: Tue Dec 31, 2002 9:10 pm
- Location: Zweibrücken bzw. Landau/Pfalz
- Contact:
Re: Hello from Serbia
Brake pads are an ease. You will find lots of them on ebay.CokiGFR125 wrote:What i need is piston , piston rings , gasket set , brake pads etc ....
Gasket (paper ones) wil also fit from other 125ccm Gileras from that time.. Crono, CX...
A good source for things like this is forum member Gottfried Hahne .
The piston is hard to get
And expensive too
It's different from the other 125ccm Gileras (maybe the CX has the same one)
A good source should be Bob Wright in GB.
The cylinder is ok?
I ask because i think that you have a sized engine. Like most of the GFRs
If you only need a piston, you should take care of the letter with which it is marked on the upper surface (A to F or so). You will need the same diameter to fit into your cylinder.
ciao joachim
- CokiGFR125
- Angstbremser
- Posts: 18
- Joined: Sun Jan 30, 2011 6:20 pm
- Location: Apatin / Vojvodina / Serbia
Re: Hello from Serbia
I mean the whole gasket set , everything possible , i like when i`me doing something to do it wright or not to do it at all.
The cylinder is good , little warn out but ok , the lettering on the piston will be an issue , but i will try to read it , and i need an oversize piston.
Joachim thank you for the info , you seem like a cool guy !
The cylinder is good , little warn out but ok , the lettering on the piston will be an issue , but i will try to read it , and i need an oversize piston.
Joachim thank you for the info , you seem like a cool guy !
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)