gilera cx125 cx 125

madmods · Post by **madmods** » Sun Oct 14, 2007 3:33 am

I finally got my bike, and most of the plastic was cracked. I ordered a set of carbon-fiber body work. Much nicer. I have to replace the chain, tires and gas lines. Here are some pictures:

Gotfried, I need a sticker set, chain guide and owners manual.

gileraXR1 · Post by **gileraXR1** » Mon Oct 15, 2007 8:38 am

Wow! Coooool!
Very good!!!!

Do you wanna to paint it???

Have a nice day!!!!

Ciao

Marco

hahne · Post by **hahne** » Mon Oct 15, 2007 5:44 pm

You will have answer tomorrow! ... bei mail ......Bye Gottfried. I am not in best codition!!!!!"

hahne · Post by **hahne** » Tue Oct 23, 2007 5:07 pm

Sorry for delay, so I was falling down from ladder again. Incl. shipment all stickers in red 82,90€. Bye Gottfried

madmods · Post by **madmods** » Thu Oct 25, 2007 9:53 am

Well project CX2 continues. I have been replacing hardware. All rusted parts are being sandblasted and repainted. Here is the rear brake getting ready for paint and the gold rk chain:

The clutch level and grip got replaced by a crg gp clutch and some pro-grips:

The front brake cylinder will be replaced by a brembo 16 x 18 radial maser cylinder made for a single disc:

The rear end got the brake caliper holder anodized in blue, sprocket carrier anodized in red, sproket done in gold. Brake pads look old, so I m going to replace them.

The out-dated and ugly speedometer will be replaced with this beautiful model from koso:

The headlight will be replaced with this:

the taillight will be replaced with this:

madmods · Post by **madmods** » Thu Oct 25, 2007 9:59 am

The wheels can not be changed so I have been photoshopping painting ideals. Which one do you like?

The bike will be repainted in italian colors. Here is the first sketch. I didn't like it. I have decided to copy the new bimota, except do the gas tank in white and carbon.

gileraXR1 · Post by **gileraXR1** » Thu Oct 25, 2007 11:24 am

Well.... I'm a purist!
I prefere the original scheme but..... Bimota scheme.... it's cool!

Ciao

Marco

Post by **gileramad** » Thu Oct 25, 2007 11:44 pm

I like this

Aendu · Post by **Aendu** » Fri Oct 26, 2007 7:26 am

Me too...

madmods · Post by **madmods** » Sun Oct 28, 2007 8:17 pm

Gottfried,
Is this available from your shop. Mine is broken.

madmods · Post by **madmods** » Fri Nov 16, 2007 9:47 am

The project continues:

madmods · Post by **madmods** » Fri Nov 16, 2007 9:52 am

The brake pads were changed. I had a hard time finding front pads until I realised they are used on over 20 different bikes.

The rotors were sandblasted and painted.

madmods · Post by **madmods** » Fri Nov 16, 2007 9:54 am

the front master brake cylinder was replaced with a brembo radial master cylinder.

madmods · Post by **madmods** » Fri Nov 16, 2007 9:57 am

The headlights arrived from germany. The tailight from italy and the other tailight from usa.

I tested the headlight:

The headlights have angel eyes:

I must make a plate to mount the headlights properly out of carbon fiber.

madmods · Post by **madmods** » Fri Nov 16, 2007 9:59 am

I have to cut out hole in the body to fit the tailights. Right now I put a piece of tape to hold the tailight for the pictures. There will be 2 tailights: