power valve

mikey · Post by **mikey** » Tue Nov 15, 2005 11:03 pm

Hey there, i'am kinda new here. I recently have come into posesion of a gilera GFR, and there seem to mis some parts. The previous owner has taken the power valve apart, and he has failed to install somekind of bearing or sealing. I hope that some one has a picture so that i can order the right parts.

mike

Post by **gileramad** » Tue Nov 15, 2005 11:10 pm

This list is from the SP01 pats-list - the parts "should" fit but I am not sure.
Maybe Markus knows since he has/had both bikes....
I think part 14 is different because that´s where the GFR has the cable for the power valve activation connected. The SP´s have a mechanical power valve activation.

mikey · Post by **mikey** » Tue Nov 15, 2005 11:23 pm

Thanks for your speedy reaction, part 7.8.9.11 seem to be missing, any idea where i can order these parts?

mikey · Post by **mikey** » Tue Nov 15, 2005 11:27 pm

Any way, the barrel looks exactly the same as the one mounted on my bike

Post by **gileramad** » Tue Nov 15, 2005 11:34 pm

You can try the usual suspects:
Gottfried
Bob
Volker

And don´t forget to show us some pictures of your bike

mikey · Post by **mikey** » Wed Nov 16, 2005 10:36 pm

the barrel on the picture has carb mounted to the barrel, on my bike the carb is mounted on the engine. Are the powervalve's the same on both engine's? Picture's aren't possible at the moment, because my digi cam is broken. The bike is in an reasonably good condition, and has run only 7500km. I bought the bike cheap as dirt, because it did not run at the time. A new sparkplug solved the problem. Once the plug was changed the bike ran like an angry hornet(besides the powervalve problem,i fixed the valve open) Only litle things need to be fixed, cosmetics, chain,etc.
The gilera is nice winterproject, besides my ducati 748 thats being overhault at the moment.

Rubberduck · Post by **Rubberduck** » Thu Nov 17, 2005 7:25 am

in my sp01 the carb is mounted on engine, and it has exact same povervalve-system....

Post by **gileramad** » Thu Nov 17, 2005 6:07 pm

Here is the sheet for the CX etc. Motors - looks also like the intake is in the cylinder but it definately istn´t. (except that there is a special version for our friends in switzerland

)

http://the.shouks.free.fr/cx/microfiches/142-00.gif

hahne · Post by **hahne** » Thu Nov 17, 2005 7:38 pm

Sorry, but I am just back from Italy, I will answer you next days!! ( I`m down at the moment!) Bye Gottfried

hahne · Post by **hahne** » Fri Nov 18, 2005 9:13 am

I must have this parts you seek. Give me all measures of parts, so I am sure! Bye Gottfried

mikey · Post by **mikey** » Tue Nov 22, 2005 9:03 pm

Dear Gottfried,

I'am told the gfr, crono, cx, share the same engine. There for the parts shown inthe exploded view must be the same as the parts i need. If that is correct, i need the following parts: 7or8, 12,15,16,17,18.
I'am not sure about part 7 or 8, because i already have one of them.
I hope that you can help me, and for a speedy reply.

Greetz mike,

mikey · Post by **mikey** » Mon Dec 12, 2005 10:03 pm

Hey Gottfried are you still there?
I have tried to send you mail, but for some reason the adress seems to be faulty I hope that you read this and can contact me. I'am in dire need of the parts that are discribed in the privious messages