Hello from Serbia

Forum für klassische und neue Gilera-Motorräder
Bulletin Board for classic and new Gilera-Motorcycles

Moderator: Joachim

Post Reply
User avatar
CokiGFR125
Angstbremser
Posts: 18
Joined: Sun Jan 30, 2011 6:20 pm
Location: Apatin / Vojvodina / Serbia

Hello from Serbia

Post by CokiGFR125 » Sun Jan 30, 2011 6:41 pm

Hello to all Gilera fans , my name is Dimitrije (Dimitij) , i recently bought 1993 Gilera GFR 125 , and i`m planning to fully restore it .
It`s in a really bad shape , i`m hoping i can get some advice from other Gilera fans ...
Thanks..

Anyhow where can i post a new thread about my GFR ?
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)

User avatar
Joachim
Gileristi
Posts: 8335
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Re: Hello from Serbia

Post by Joachim » Sun Jan 30, 2011 7:26 pm

CokiGFR125 wrote: Anyhow where can i post a new thread about my GFR ?
Just right here ;)

Good luck while finding parts. Everything seems to be very rare :(
If you need fairing parts, i can offer a source for replica parts from glass fibre.

ciao joachim
Image

User avatar
CokiGFR125
Angstbremser
Posts: 18
Joined: Sun Jan 30, 2011 6:20 pm
Location: Apatin / Vojvodina / Serbia

Re: Hello from Serbia

Post by CokiGFR125 » Sun Jan 30, 2011 9:36 pm

Thank`s Joachim , i will make my own parts , i mean the fiber glass.
What i need is piston , piston rings , gasket set , brake pads etc ....
I will post a new build thread about my GFR.
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)

User avatar
Joachim
Gileristi
Posts: 8335
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Re: Hello from Serbia

Post by Joachim » Sun Jan 30, 2011 9:48 pm

CokiGFR125 wrote:What i need is piston , piston rings , gasket set , brake pads etc ....
Brake pads are an ease. You will find lots of them on ebay.
Gasket (paper ones) wil also fit from other 125ccm Gileras from that time.. Crono, CX...

A good source for things like this is forum member Gottfried Hahne .

The piston is hard to get :|
And expensive too :?
It's different from the other 125ccm Gileras (maybe the CX has the same one)
A good source should be Bob Wright in GB.
The cylinder is ok?
I ask because i think that you have a sized engine. Like most of the GFRs ;)
If you only need a piston, you should take care of the letter with which it is marked on the upper surface (A to F or so). You will need the same diameter to fit into your cylinder.

ciao joachim
Image

User avatar
CokiGFR125
Angstbremser
Posts: 18
Joined: Sun Jan 30, 2011 6:20 pm
Location: Apatin / Vojvodina / Serbia

Re: Hello from Serbia

Post by CokiGFR125 » Sun Jan 30, 2011 10:36 pm

I mean the whole gasket set , everything possible , i like when i`me doing something to do it wright or not to do it at all.
The cylinder is good , little warn out but ok , the lettering on the piston will be an issue , but i will try to read it , and i need an oversize piston.
Joachim thank you for the info , you seem like a cool guy !
1993 Piece of junk Gilera GFR 125 (hope to see it shine really soon)

Post Reply