Carburator factory settings

Forum für klassische und neue Gilera-Motorräder
Bulletin Board for classic and new Gilera-Motorcycles

Moderator: Joachim

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Post by Joachim » Tue Apr 22, 2008 3:41 pm

Bad luck :(
Don't forget to check the ground wiring to.
Maybe.....


ciao joachim
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

Chain reaction !!!!

Post by linju62 » Tue Apr 22, 2008 5:54 pm

From carburator to ignition.

Did some measuring with stator coils and fin out that one reading is 10 ohms lower than it should be so need to get flywheel out for closer check of the stator.
Who knows the measures for the flywheel puller tool?
Thread to fix it to flywheel and the bolt size + also need to know which handed the main thread shoud be.

Thanks in advance
Image

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Post by Joachim » Tue Apr 22, 2008 7:13 pm

I'm not shure... maybe Gottfried can give you a better answer.

M 27x1 RH?

ciao Joachim
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

size of puller

Post by linju62 » Wed Apr 23, 2008 7:05 pm

Hi is there anybody who can verify Joachims toughs about the size of flywheel puller for SP01?

Also if somebody have the charging coil on desk or can easily measure the coil between that blue wire and ground please tell me the result.

Thanks JukkaImage
Image

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Post by Joachim » Sun Apr 27, 2008 3:41 pm

Joachim wrote: M 27x1 RH?
Wrong :(

M26 x1,0 RH
I've checked back the flywheel of my GFR.
I bought it last year new. Part number is 326632.
I got it sold as a SP01/02 one.
The original GFR one is almost the same. It is only a little bit lighter because Luigi has turned down a few mm on the outside.
You may measure the exact inside of the thread of your Flywheel, send it to me and i will compare it with mine. Just to be shure
My puller is from Buzetti. You may get one in nearly every shop that sells scooter parts. Or from Gottfried :)

ciao joachim
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

size of puller

Post by linju62 » Sun Apr 27, 2008 5:27 pm

Hi Joachim and thanks for the effort.

I measured with caliper the dimension and it was 25mm.

I was wondering about the readings of the coil too (capacitor charging coil)
and the reading according the workshop manual of crono says that it should be 46 ohms between blue and ground.
I think SP 01 should be pretty much same?
Mine was 34ohms.
If resistance is that much wrong (20%) I think that might be the cause for week spark in the plug?

BR Jukka
Image

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Re: size of puller

Post by Joachim » Sun Apr 27, 2008 6:46 pm

linju62 wrote:I measured with caliper the dimension and it was 25mm.
hmmm.. that could be M 26x1,0.
But in most of the cases the inner diameter is bigger than it should be.
So....
The pullers are not that expensive. I would start with M 26 ;)
Did you have a spare parts list of your SP and could look after the part number I have send?

If resistance is that much wrong (20%) I think that might be the cause for week spark in the plug?
Measuring such low resistances may be a problem.
One solution is just to test it. If you can find a second one :)

ciao Joachim
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

Post by linju62 » Sun Apr 27, 2008 6:53 pm

Hi

Just look at the SP01 spare catalog and the spare number looks same what you said

326632 Rotor ESV in catalog
but there is a second number for rotor too 326630 Rotor.

What might be the difference?

BR Jukka[/quote]
Image

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Post by Joachim » Sun Apr 27, 2008 8:47 pm

linju62 wrote:What might be the difference?
The size of the thread for the puller :)

ciao Joachim <just kidding>
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

Coil

Post by linju62 » Mon Apr 28, 2008 9:44 am

Hi Joachim

you hit the point when said "if you can find one"
That I would like to know where I can get one?

Gottfried maybe?

BR Jukka[/quote]
Image

User avatar
linju62
Angstbremser
Posts: 14
Joined: Thu Apr 10, 2008 7:09 pm
Location: Finland

Hooray!!!

Post by linju62 » Sun May 11, 2008 1:09 pm

Got it running yesterday.
Problem was the capacitor charging coil 34 ohms instead of 46 ohms.

But same time I found that brand new CDI box was broken too, throw old in and first try the engine woke up.

Thanks for the help to all who bothered to answer.

BR Jukka :)
Image

User avatar
Joachim
Gileristi
Posts: 8478
Joined: Tue Dec 31, 2002 9:10 pm
Location: Zweibrücken bzw. Landau/Pfalz
Contact:

Post by Joachim » Sun May 11, 2008 8:18 pm

*thumb*

ciao Joachim who's is not running due to some brake problems>
Image

lucianbeleuzu
Tank-Reserve-Benutzer
Posts: 1
Joined: Wed May 14, 2008 9:53 am

Gilera DNA 50

Post by lucianbeleuzu » Fri May 30, 2008 9:50 am

Ok... i have a Gilera DNA 50, and in this weekend i want to clean his carb.
I will remove it from the engine and put it in a carb liquid cleaner. What or how do you recommend to use for cleaning? Something like diesel, fuel, or diluent.

The problem is that i need some parts for my Gilera DNA 50... and i must identify those pieces from the Vintage catalogue, can you help me and tell me what components from there are for Gilera DNA 50?

Im looking for coil, flywheel, CDI, regulator, but i don`t know wich them are for Gilera DNA 50. Please indicate me the pieces for my "motor" :D

Ah by the way... sorry about my english, im a romanian... and i haven`t speaked or wrote in english for almost 4 years.

8)

User avatar
hahne
Gileristi
Posts: 2873
Joined: Mon Dec 30, 2002 8:12 am
Location: Aussernzell
Contact:

Post by hahne » Fri May 30, 2008 10:28 am

Puller M26 X 1 I have. Bye Gottfried

Post Reply